GPIS GPR Concrete Scanning and Imaging

11/03/2026

🔎 BELOW THE SURFACE. BEFORE THE NEXT STEP.

📍 Chicago, Illinois

Today, GPIS Concrete Scanning & Imaging teamed up with PNK Design+Build to uncover important details inside existing foundation walls.

🔵 Reinforcement located and marked
📏 Approximate target depths and spacing documented
📐 Wall thickness and exposed footing measurements recorded
📸 Detailed photo report prepared for engineering review

The project team also performed soil testing and collected concrete cores for testing—bringing together information about the soil, concrete, and embedded reinforcement.

Our role: non-invasive GPR scanning and clear field documentation to help the team plan its next steps.

From the marks on the wall to the dimensions on the drawing, every detail helps tell the story. 👷‍♂️

⚡ SCAN BEFORE YOU CUT.

GPIS Concrete Scanning & Imaging
📞 773-720-1069
🌐 GPISGPR.com
📍 Serving Chicagoland & Northwest Indiana

10/02/2026

🔎 Before the concrete is cut, know what’s beneath it.

Today, GPIS Concrete Scanning and Imaging scanned the basement slab at Winston Tower 3 in Chicago for North Shore Plumbing ahead of trenching for new plumbing.

The approximately 10-inch-thick slab contained intersecting rebar and multiple conduit / possible conduit routes at varying depths—important conflicts to identify before cutting.

🔵 Blue markings: rebar
🔴 Red with white stripes: conduits / possible conduits
↔️ Depth labels and arrows: estimated depths and interpreted routes

We documented the findings in a detailed end-of-job report and recommended a minimum 3-inch clearance in every direction from all anomaly markings. Any crossings within the proposed trench require further review before work proceeds.

GPR scanning helps reduce the risk of costly strikes, repairs, and delays. It’s an important step in planning your next cut, core, or drill.

📞 773-720-1069
🌐 GPISGPR.com

09/09/2026

Another successful GPR concrete-scanning project completed by GPIS at Fresh Wash Laundry LLC in South Chicago, Illinois.

Before concrete cutting began, GPIS scanned the designated floor area and identified:

✅ Three conduit paths at approximately 5 inches below the surface
✅ 6-by-6 wire mesh approximately 3 inches below the surface
✅ Concrete thickness ranging from approximately 4.5 to 5 inches

Each conduit path was traced and clearly marked directly on the concrete. A minimum 3-inch safety clearance was established around all conduit markings to help the cutting contractor avoid costly damage, electrical hazards, and project delays.

Know what’s inside the concrete before you cut, core, or drill.

📞 (773) 720-1069
📧 [email protected]
🌐 GPISGPR.com

SCAN BEFORE YOU CUT!

09/02/2026

Today’s project in Winnetka, Illinois:

GPIS performed GPR concrete scanning of a residential garage floor to assist with planning the installation of a new car lift.

This was not a standard concrete slab. The floor consisted of a reinforced concrete wear slab, sloped topping, waterproofing, and prestressed hollow-core plank over a finished basement.

We scanned from both the garage surface and the basement underside to:

• Map reinforcing steel
• Identify the hollow-core layout
• Interpret the prestressing strand pattern
• Compare the proposed lift location with the existing lift area
• Document the slab assembly and approximate depths

The results provide the structural engineer and lift installer with valuable information for evaluating the lift location and anchorage requirements.

Scan before you drill, cut, or anchor.

GPIS Concrete Scanning & Imaging
📞 773-720-1069
🌐 GPISGPR.com

08/21/2026

🔍 GPR CONCRETE SCANNING | JEWEL-OSCO – SOUTH HOLLAND, IL

Another detailed concrete investigation completed by GPIS Concrete Scanning & Imaging, this time for Cushing Terrell Mechanical Engineers at the Jewel-Osco facility in South Holland, Illinois.

The purpose of this scan was different from a typical saw-cut or core-drilling layout. The engineering team needed accurate information about the existing floor construction to help evaluate the slab for new mechanical equipment.

Using Ground Penetrating Radar (GPR), GPIS mapped and physically marked the existing precast floor system, identifying:

🔹 Precast panel locations and panel joints
🔹 Hollow-core locations and centerlines
🔹 Prestressed/high-tensile reinforcement
🔹 Wire-mesh reinforcement within the topping slab
🔹 Approximate reinforcement depths
🔹 Topping slab and precast panel configuration
🔹 Overall floor-system thickness

The scan identified approximately 8" precast panels with a 1½"–2" topping slab, producing an overall floor thickness of approximately 9½"–10" in the investigated areas.

Because this information was being collected for structural/mechanical engineering evaluation rather than cutting or coring, detailed field markings were placed directly on the floor so the engineers could clearly see how the existing precast system was constructed and where critical internal features were located.

📍 Jewel-Osco – South Holland, Illinois
🏗️ Client: Cushing Terrell Mechanical Engineers

GPR isn't only about finding a safe place to drill. It can also provide valuable information about an existing concrete structure when drawings are limited or field verification is needed.

Know what's in the concrete before making decisions above it.

GPIS Concrete Scanning & Imaging
📞 773-720-1069
🌐 GPISGPR.com
✉️ [email protected]

07/28/2026

concrete scanning and imaging

07/20/2026

👀 What's hiding beneath your concrete?

Most people look at a concrete floor and see... concrete.

We see electrical conduits feeding an entire building, reinforcing steel holding the structure together, post-tension cables under thousands of pounds of force, plumbing lines, and sometimes surprises that were never shown on the original plans.

One wrong cut can shut down a business, damage expensive equipment, delay a project, or worse—injure someone.

That's why we do what we do.

At GPIS Concrete Scanning & Imaging, every scan is about giving contractors the confidence to make the first cut safely. We turn the unknown into a clear plan before the saw ever touches the concrete.

❓What's the strangest thing you've ever found hidden inside a wall or concrete slab? Tell us in the comments—we've seen some interesting ones over the years.

📍Serving Illinois & Northwest Indiana

📞 773-720-1069
🌐 GPISGPR.com
📧 [email protected]

Don't guess. Scan first. Everyone deserves to go home safe.

07/04/2026

🇺🇸 Happy 4th of July from GPIS Ground Penetrating Radar Imaging Solutions! 🇺🇸
Today we celebrate 250 years of American independence and the freedoms that make this country great. While you're enjoying fireworks, cookouts, and time with family and friends, we also want to recognize something that's just as important—making it home safely.
At GPIS, safety is at the heart of everything we do. Before concrete is cut, cored, or drilled, we help contractors locate hidden rebar, post-tension cables, conduit, and other embedded hazards using Ground Penetrating Radar (GPR). Every scan helps reduce risk, prevent costly damage, and most importantly, protect the people on the job.
The same reason we work safely is the same reason we celebrate today—to get home to the people who matter most.
Have a safe, fun, and memorable Independence Day!
🇺🇸 Celebrating 250 Years of Freedom. Protecting Every Cut. Every Core. Every Crew. 🇺🇸

07/03/2026